SafeASP - PCB floorplan 84 x 32 mm

84 x 32 mm, 2 layers. Signal flow left to right: USB-C, V-USB, ATmega8A, level shifter, ISP headers. One zoomed drawing, one dashed silkscreen box and one X / Y table per block; tick each part as you place it in EasyEDA (saved in this browser).

Design stage. Planned design, not a finished schematic or PCB and not built yet: nets come from tools/data.py, pin numbers of U1, U4, U5 were read from the datasheets, but every symbol and footprint must still be checked in EasyEDA.
Board sizeFloor planUSB-CV-USBATMEGA8ALEVEL SHIFTTARGET POWERISP 10 / 6 PINNetsStepsplaced 0 / 45

Board size: 84 x 32 mm

2 layers, 1.6 mm FR-4, 1 oz copper, 84 x 32 mm, 2 mm corners, two M3 holes (3.2 mm, non-plated) on the USB end. Parts add up to about 881 mm² of 2688 mm² (33 %). The v5 board was 68 x 31 mm; V6 is longer because of the level shifter, the target-power block and the second ISP header. It stays far below 100 x 100 mm (cheapest PCB price tier).

Outline and holes

ItemX mmY mmSize
Board outline0 - 840 - 3284 x 32, corner radius 2 mm
MH1 M3 hole3.53.53.2 mm, non-plated
MH2 M3 hole3.528.53.2 mm, non-plated

Edge plan

The checker (tools/layout.py) confirmed: no overlaps, every part inside its own silkscreen box, no box touching another box or a mounting hole.

Floor plandashed boxes = silkscreen boxes; click a part to tick it

1020304050607080102030USB-CV-USBATMEGA8ALEVEL SHIFTTARGET POWERISP 10 / 6 PINJ1: USB-C 16-pin receptacle (USB 2.0) [C165948] x=3.8 y=16.0 mmJ1U2: USBLC6-2SC6 ESD on D+ / D- [C7519] x=11.5 y=16.0 mmU2R1: 5.1 k 1206, CC1 pull-down [C26033] x=11.5 y=20.4 mmR1R2: 5.1 k 1206, CC2 pull-down [C26033] x=11.5 y=11.6 mmR2F1: PTC 500 mA 1206, VBUS to +5V [C163512] x=11.5 y=23.4 mmF1C2: 100 nF 1206 on VBUS [C24497] x=11.5 y=8.8 mmC2R3: 68 R 1206, D+ series [C17976] x=18.5 y=19.5 mmR3D1: 3.6 V zener, D+ clamp [C725453] x=23.9 y=19.5 mmD1R4: 68 R 1206, D- series [C17976] x=18.5 y=12.5 mmR4D2: 3.6 V zener, D- clamp [C725453] x=23.9 y=12.5 mmD2R5: 2.2 k 1206, D- pull-up (low speed) [C17948] x=18.5 y=8.6 mmR5C1: 10 uF 1206, +5V bulk [C9807] x=18.5 y=24.4 mmC1U1: ATmega8A-AU, TQFP-32 [C16190] x=37.0 y=16.0 mmU1Y1: 12 MHz crystal 3225 [C9002] x=29.6 y=12.6 mmY1C3: 22 pF 0805, XTAL1 load [C1804] x=29.6 y=9.0 mmC3C4: 22 pF 0805, XTAL2 load [C1804] x=29.6 y=16.4 mmC4C5: 100 nF 1206, VCC pin 4 [C24497] x=37.6 y=23.0 mmC5C7: 100 nF 1206, AVCC pin 18 [C24497] x=42.6 y=23.0 mmC7R6: 10 k 1206, RESET pull-up [C17902] x=31.0 y=23.0 mmR6C6: 100 nF 1206, VCC pin 6 [C24497] x=37.0 y=9.0 mmC6LED1: Red LED: programming (PC1 low) [C965798] x=31.0 y=26.8 mmLED1R7: 1 k 1206, LED1 series [C4410] x=36.0 y=26.8 mmR7LED2: Green LED: USB ready (PC0 low) [C2986059] x=31.0 y=29.6 mmLED2R8: 1 k 1206, LED2 series [C4410] x=36.0 y=29.6 mmR8J4: 2x3 header: flash THIS ATmega8A (self-programming port) [C65114] x=37.5 y=3.6 mmJ4JP2: 1x2 header: slow SCK jumper (PC2 to GND) [C492401] x=29.8 y=4.0 mmJP2U4: 74LVC8T245PW 8-bit dual-supply transceiver, TSSOP-24 [C458788] x=50.2 y=10.2 mmU4C10: 100 nF 1206, U4 VCCA [C24497] x=50.2 y=16.6 mmC10U5: 74LVC1T45GW 1-bit dual-supply transceiver (MISO back), SC-88 [C478004] x=55.6 y=16.4 mmU5R10: 10 k 1206, OE# pull-up (outputs off while the ATmega8A is in reset) [C17902] x=55.6 y=11.6 mmR10R11: 100 k 1206, MOSI_M pull-down (no floating input) [C17900] x=55.6 y=5.0 mmR11C12: 100 nF 1206, U5 VCCA [C24497] x=59.4 y=16.0 mmC12R12: 100 k 1206, SCK_M pull-down [C17900] x=59.4 y=9.6 mmR12R13: 100 k 1206, RST_M pull-down [C17900] x=59.4 y=3.6 mmR13C13: 100 nF 1206, U5 VCCB [C24497] x=63.0 y=16.0 mmC13C11: 100 nF 1206, U4 VCCB [C24497] x=63.0 y=9.6 mmC11U3: AP2112K-3.3 LDO, SOT-25 [C51118] x=48.8 y=29.2 mmU3C8: 10 uF 1206, LDO input [C9807] x=53.4 y=29.2 mmC8C9: 10 uF 1206, LDO output [C9807] x=58.2 y=29.2 mmC9LED3: Yellow LED: powering the target [C965803] x=48.6 y=25.4 mmLED3R9: 1 k 1206, LED3 series [C4410] x=53.4 y=25.4 mmR9F2: PTC 200 mA 1206, target supply limit [C207035] x=58.2 y=25.4 mmF2JP1: 1x3 header: target supply 5 V (1-2) / 3.3 V (2-3) / off [C492402] x=51.0 y=21.7 mmJP1J2: 2x5 box header: standard AVR 10-pin ISP [C5665] x=79.0 y=16.0 mmJ2J3: 2x3 header: standard AVR 6-pin ISP [C65114] x=68.4 y=16.0 mmJ3

USB-C0 / 6 placed · box x 0.0 to 14.6, y 7.4 to 24.8 mm

USB-CV-USBATMEGA8ALEVEL SHIFTTARGET POWERISP 10 / 6 PINJ1: USB-C 16-pin receptacle (USB 2.0) [C165948] x=3.8 y=16.0 mmJ1U2: USBLC6-2SC6 ESD on D+ / D- [C7519] x=11.5 y=16.0 mmU2R1: 5.1 k 1206, CC1 pull-down [C26033] x=11.5 y=20.4 mmR1R2: 5.1 k 1206, CC2 pull-down [C26033] x=11.5 y=11.6 mmR2F1: PTC 500 mA 1206, VBUS to +5V [C163512] x=11.5 y=23.4 mmF1C2: 100 nF 1206 on VBUS [C24497] x=11.5 y=8.8 mmC2R3: 68 R 1206, D+ series [C17976] x=18.5 y=19.5 mmR3D1: 3.6 V zener, D+ clamp [C725453] x=23.9 y=19.5 mmD1R4: 68 R 1206, D- series [C17976] x=18.5 y=12.5 mmR4D2: 3.6 V zener, D- clamp [C725453] x=23.9 y=12.5 mmD2R5: 2.2 k 1206, D- pull-up (low speed) [C17948] x=18.5 y=8.6 mmR5C1: 10 uF 1206, +5V bulk [C9807] x=18.5 y=24.4 mmC1U1: ATmega8A-AU, TQFP-32 [C16190] x=37.0 y=16.0 mmU1Y1: 12 MHz crystal 3225 [C9002] x=29.6 y=12.6 mmY1C3: 22 pF 0805, XTAL1 load [C1804] x=29.6 y=9.0 mmC3C4: 22 pF 0805, XTAL2 load [C1804] x=29.6 y=16.4 mmC4C5: 100 nF 1206, VCC pin 4 [C24497] x=37.6 y=23.0 mmC5C7: 100 nF 1206, AVCC pin 18 [C24497] x=42.6 y=23.0 mmC7R6: 10 k 1206, RESET pull-up [C17902] x=31.0 y=23.0 mmR6C6: 100 nF 1206, VCC pin 6 [C24497] x=37.0 y=9.0 mmC6LED1: Red LED: programming (PC1 low) [C965798] x=31.0 y=26.8 mmLED1R7: 1 k 1206, LED1 series [C4410] x=36.0 y=26.8 mmR7LED2: Green LED: USB ready (PC0 low) [C2986059] x=31.0 y=29.6 mmLED2R8: 1 k 1206, LED2 series [C4410] x=36.0 y=29.6 mmR8J4: 2x3 header: flash THIS ATmega8A (self-programming port) [C65114] x=37.5 y=3.6 mmJ4JP2: 1x2 header: slow SCK jumper (PC2 to GND) [C492401] x=29.8 y=4.0 mmJP2U4: 74LVC8T245PW 8-bit dual-supply transceiver, TSSOP-24 [C458788] x=50.2 y=10.2 mmU4C10: 100 nF 1206, U4 VCCA [C24497] x=50.2 y=16.6 mmC10U5: 74LVC1T45GW 1-bit dual-supply transceiver (MISO back), SC-88 [C478004] x=55.6 y=16.4 mmU5R10: 10 k 1206, OE# pull-up (outputs off while the ATmega8A is in reset) [C17902] x=55.6 y=11.6 mmR10R11: 100 k 1206, MOSI_M pull-down (no floating input) [C17900] x=55.6 y=5.0 mmR11C12: 100 nF 1206, U5 VCCA [C24497] x=59.4 y=16.0 mmC12R12: 100 k 1206, SCK_M pull-down [C17900] x=59.4 y=9.6 mmR12R13: 100 k 1206, RST_M pull-down [C17900] x=59.4 y=3.6 mmR13C13: 100 nF 1206, U5 VCCB [C24497] x=63.0 y=16.0 mmC13C11: 100 nF 1206, U4 VCCB [C24497] x=63.0 y=9.6 mmC11U3: AP2112K-3.3 LDO, SOT-25 [C51118] x=48.8 y=29.2 mmU3C8: 10 uF 1206, LDO input [C9807] x=53.4 y=29.2 mmC8C9: 10 uF 1206, LDO output [C9807] x=58.2 y=29.2 mmC9LED3: Yellow LED: powering the target [C965803] x=48.6 y=25.4 mmLED3R9: 1 k 1206, LED3 series [C4410] x=53.4 y=25.4 mmR9F2: PTC 200 mA 1206, target supply limit [C207035] x=58.2 y=25.4 mmF2JP1: 1x3 header: target supply 5 V (1-2) / 3.3 V (2-3) / off [C492402] x=51.0 y=21.7 mmJP1J2: 2x5 box header: standard AVR 10-pin ISP [C5665] x=79.0 y=16.0 mmJ2J3: 2x3 header: standard AVR 6-pin ISP [C65114] x=68.4 y=16.0 mmJ3
RefPartLCSCX mmY mmRotSize mm (est.)
U2USBLC6-2SC6 ESD on D+ / D-C751911.516.00°3.4 x 3.2
J1USB-C 16-pin receptacle (USB 2.0)C1659483.816.00°7.5 x 9.0
C2100 nF 1206 on VBUSC2449711.58.80°4.6 x 2.6
F1PTC 500 mA 1206, VBUS to +5VC16351211.523.40°4.6 x 2.6
R15.1 k 1206, CC1 pull-downC2603311.520.40°4.6 x 2.6
R25.1 k 1206, CC2 pull-downC2603311.511.60°4.6 x 2.6

V-USB0 / 6 placed · box x 15.4 to 26.6, y 6.0 to 27.0 mm

USB-CV-USBATMEGA8ALEVEL SHIFTTARGET POWERISP 10 / 6 PINJ1: USB-C 16-pin receptacle (USB 2.0) [C165948] x=3.8 y=16.0 mmJ1U2: USBLC6-2SC6 ESD on D+ / D- [C7519] x=11.5 y=16.0 mmU2R1: 5.1 k 1206, CC1 pull-down [C26033] x=11.5 y=20.4 mmR1R2: 5.1 k 1206, CC2 pull-down [C26033] x=11.5 y=11.6 mmR2F1: PTC 500 mA 1206, VBUS to +5V [C163512] x=11.5 y=23.4 mmF1C2: 100 nF 1206 on VBUS [C24497] x=11.5 y=8.8 mmC2R3: 68 R 1206, D+ series [C17976] x=18.5 y=19.5 mmR3D1: 3.6 V zener, D+ clamp [C725453] x=23.9 y=19.5 mmD1R4: 68 R 1206, D- series [C17976] x=18.5 y=12.5 mmR4D2: 3.6 V zener, D- clamp [C725453] x=23.9 y=12.5 mmD2R5: 2.2 k 1206, D- pull-up (low speed) [C17948] x=18.5 y=8.6 mmR5C1: 10 uF 1206, +5V bulk [C9807] x=18.5 y=24.4 mmC1U1: ATmega8A-AU, TQFP-32 [C16190] x=37.0 y=16.0 mmU1Y1: 12 MHz crystal 3225 [C9002] x=29.6 y=12.6 mmY1C3: 22 pF 0805, XTAL1 load [C1804] x=29.6 y=9.0 mmC3C4: 22 pF 0805, XTAL2 load [C1804] x=29.6 y=16.4 mmC4C5: 100 nF 1206, VCC pin 4 [C24497] x=37.6 y=23.0 mmC5C7: 100 nF 1206, AVCC pin 18 [C24497] x=42.6 y=23.0 mmC7R6: 10 k 1206, RESET pull-up [C17902] x=31.0 y=23.0 mmR6C6: 100 nF 1206, VCC pin 6 [C24497] x=37.0 y=9.0 mmC6LED1: Red LED: programming (PC1 low) [C965798] x=31.0 y=26.8 mmLED1R7: 1 k 1206, LED1 series [C4410] x=36.0 y=26.8 mmR7LED2: Green LED: USB ready (PC0 low) [C2986059] x=31.0 y=29.6 mmLED2R8: 1 k 1206, LED2 series [C4410] x=36.0 y=29.6 mmR8J4: 2x3 header: flash THIS ATmega8A (self-programming port) [C65114] x=37.5 y=3.6 mmJ4JP2: 1x2 header: slow SCK jumper (PC2 to GND) [C492401] x=29.8 y=4.0 mmJP2U4: 74LVC8T245PW 8-bit dual-supply transceiver, TSSOP-24 [C458788] x=50.2 y=10.2 mmU4C10: 100 nF 1206, U4 VCCA [C24497] x=50.2 y=16.6 mmC10U5: 74LVC1T45GW 1-bit dual-supply transceiver (MISO back), SC-88 [C478004] x=55.6 y=16.4 mmU5R10: 10 k 1206, OE# pull-up (outputs off while the ATmega8A is in reset) [C17902] x=55.6 y=11.6 mmR10R11: 100 k 1206, MOSI_M pull-down (no floating input) [C17900] x=55.6 y=5.0 mmR11C12: 100 nF 1206, U5 VCCA [C24497] x=59.4 y=16.0 mmC12R12: 100 k 1206, SCK_M pull-down [C17900] x=59.4 y=9.6 mmR12R13: 100 k 1206, RST_M pull-down [C17900] x=59.4 y=3.6 mmR13C13: 100 nF 1206, U5 VCCB [C24497] x=63.0 y=16.0 mmC13C11: 100 nF 1206, U4 VCCB [C24497] x=63.0 y=9.6 mmC11U3: AP2112K-3.3 LDO, SOT-25 [C51118] x=48.8 y=29.2 mmU3C8: 10 uF 1206, LDO input [C9807] x=53.4 y=29.2 mmC8C9: 10 uF 1206, LDO output [C9807] x=58.2 y=29.2 mmC9LED3: Yellow LED: powering the target [C965803] x=48.6 y=25.4 mmLED3R9: 1 k 1206, LED3 series [C4410] x=53.4 y=25.4 mmR9F2: PTC 200 mA 1206, target supply limit [C207035] x=58.2 y=25.4 mmF2JP1: 1x3 header: target supply 5 V (1-2) / 3.3 V (2-3) / off [C492402] x=51.0 y=21.7 mmJP1J2: 2x5 box header: standard AVR 10-pin ISP [C5665] x=79.0 y=16.0 mmJ2J3: 2x3 header: standard AVR 6-pin ISP [C65114] x=68.4 y=16.0 mmJ3
RefPartLCSCX mmY mmRotSize mm (est.)
C110 uF 1206, +5V bulkC980718.524.40°4.6 x 2.6
D13.6 V zener, D+ clampC72545323.919.50°3.8 x 1.8
D23.6 V zener, D- clampC72545323.912.50°3.8 x 1.8
R368 R 1206, D+ seriesC1797618.519.50°4.6 x 2.6
R468 R 1206, D- seriesC1797618.512.50°4.6 x 2.6
R52.2 k 1206, D- pull-up (low speed)C1794818.58.60°4.6 x 2.6

ATMEGA8A0 / 14 placed · box x 27.2 to 46.0, y 0.6 to 31.4 mm

USB-CV-USBATMEGA8ALEVEL SHIFTTARGET POWERISP 10 / 6 PINJ1: USB-C 16-pin receptacle (USB 2.0) [C165948] x=3.8 y=16.0 mmJ1U2: USBLC6-2SC6 ESD on D+ / D- [C7519] x=11.5 y=16.0 mmU2R1: 5.1 k 1206, CC1 pull-down [C26033] x=11.5 y=20.4 mmR1R2: 5.1 k 1206, CC2 pull-down [C26033] x=11.5 y=11.6 mmR2F1: PTC 500 mA 1206, VBUS to +5V [C163512] x=11.5 y=23.4 mmF1C2: 100 nF 1206 on VBUS [C24497] x=11.5 y=8.8 mmC2R3: 68 R 1206, D+ series [C17976] x=18.5 y=19.5 mmR3D1: 3.6 V zener, D+ clamp [C725453] x=23.9 y=19.5 mmD1R4: 68 R 1206, D- series [C17976] x=18.5 y=12.5 mmR4D2: 3.6 V zener, D- clamp [C725453] x=23.9 y=12.5 mmD2R5: 2.2 k 1206, D- pull-up (low speed) [C17948] x=18.5 y=8.6 mmR5C1: 10 uF 1206, +5V bulk [C9807] x=18.5 y=24.4 mmC1U1: ATmega8A-AU, TQFP-32 [C16190] x=37.0 y=16.0 mmU1Y1: 12 MHz crystal 3225 [C9002] x=29.6 y=12.6 mmY1C3: 22 pF 0805, XTAL1 load [C1804] x=29.6 y=9.0 mmC3C4: 22 pF 0805, XTAL2 load [C1804] x=29.6 y=16.4 mmC4C5: 100 nF 1206, VCC pin 4 [C24497] x=37.6 y=23.0 mmC5C7: 100 nF 1206, AVCC pin 18 [C24497] x=42.6 y=23.0 mmC7R6: 10 k 1206, RESET pull-up [C17902] x=31.0 y=23.0 mmR6C6: 100 nF 1206, VCC pin 6 [C24497] x=37.0 y=9.0 mmC6LED1: Red LED: programming (PC1 low) [C965798] x=31.0 y=26.8 mmLED1R7: 1 k 1206, LED1 series [C4410] x=36.0 y=26.8 mmR7LED2: Green LED: USB ready (PC0 low) [C2986059] x=31.0 y=29.6 mmLED2R8: 1 k 1206, LED2 series [C4410] x=36.0 y=29.6 mmR8J4: 2x3 header: flash THIS ATmega8A (self-programming port) [C65114] x=37.5 y=3.6 mmJ4JP2: 1x2 header: slow SCK jumper (PC2 to GND) [C492401] x=29.8 y=4.0 mmJP2U4: 74LVC8T245PW 8-bit dual-supply transceiver, TSSOP-24 [C458788] x=50.2 y=10.2 mmU4C10: 100 nF 1206, U4 VCCA [C24497] x=50.2 y=16.6 mmC10U5: 74LVC1T45GW 1-bit dual-supply transceiver (MISO back), SC-88 [C478004] x=55.6 y=16.4 mmU5R10: 10 k 1206, OE# pull-up (outputs off while the ATmega8A is in reset) [C17902] x=55.6 y=11.6 mmR10R11: 100 k 1206, MOSI_M pull-down (no floating input) [C17900] x=55.6 y=5.0 mmR11C12: 100 nF 1206, U5 VCCA [C24497] x=59.4 y=16.0 mmC12R12: 100 k 1206, SCK_M pull-down [C17900] x=59.4 y=9.6 mmR12R13: 100 k 1206, RST_M pull-down [C17900] x=59.4 y=3.6 mmR13C13: 100 nF 1206, U5 VCCB [C24497] x=63.0 y=16.0 mmC13C11: 100 nF 1206, U4 VCCB [C24497] x=63.0 y=9.6 mmC11U3: AP2112K-3.3 LDO, SOT-25 [C51118] x=48.8 y=29.2 mmU3C8: 10 uF 1206, LDO input [C9807] x=53.4 y=29.2 mmC8C9: 10 uF 1206, LDO output [C9807] x=58.2 y=29.2 mmC9LED3: Yellow LED: powering the target [C965803] x=48.6 y=25.4 mmLED3R9: 1 k 1206, LED3 series [C4410] x=53.4 y=25.4 mmR9F2: PTC 200 mA 1206, target supply limit [C207035] x=58.2 y=25.4 mmF2JP1: 1x3 header: target supply 5 V (1-2) / 3.3 V (2-3) / off [C492402] x=51.0 y=21.7 mmJP1J2: 2x5 box header: standard AVR 10-pin ISP [C5665] x=79.0 y=16.0 mmJ2J3: 2x3 header: standard AVR 6-pin ISP [C65114] x=68.4 y=16.0 mmJ3
RefPartLCSCX mmY mmRotSize mm (est.)
U1ATmega8A-AU, TQFP-32C1619037.016.00°9.2 x 9.2
J42x3 header: flash THIS ATmega8A (self-programming port)C6511437.53.60°7.6 x 5.1
JP21x2 header: slow SCK jumper (PC2 to GND)C49240129.84.00°5.1 x 2.5
C322 pF 0805, XTAL1 loadC180429.69.00°3.0 x 1.8
C422 pF 0805, XTAL2 loadC180429.616.40°3.0 x 1.8
C5100 nF 1206, VCC pin 4C2449737.623.00°4.6 x 2.6
C6100 nF 1206, VCC pin 6C2449737.09.00°4.6 x 2.6
C7100 nF 1206, AVCC pin 18C2449742.623.00°4.6 x 2.6
LED1Red LED: programming (PC1 low)C96579831.026.80°2.6 x 1.6
LED2Green LED: USB ready (PC0 low)C298605931.029.60°2.6 x 1.6
R610 k 1206, RESET pull-upC1790231.023.00°4.6 x 2.6
R71 k 1206, LED1 seriesC441036.026.80°4.6 x 2.6
R81 k 1206, LED2 seriesC441036.029.60°4.6 x 2.6
Y112 MHz crystal 3225C900229.612.60°2.7 x 3.4

LEVEL SHIFT0 / 10 placed · box x 46.6 to 64.4, y 0.6 to 19.0 mm

USB-CV-USBATMEGA8ALEVEL SHIFTTARGET POWERISP 10 / 6 PINJ1: USB-C 16-pin receptacle (USB 2.0) [C165948] x=3.8 y=16.0 mmJ1U2: USBLC6-2SC6 ESD on D+ / D- [C7519] x=11.5 y=16.0 mmU2R1: 5.1 k 1206, CC1 pull-down [C26033] x=11.5 y=20.4 mmR1R2: 5.1 k 1206, CC2 pull-down [C26033] x=11.5 y=11.6 mmR2F1: PTC 500 mA 1206, VBUS to +5V [C163512] x=11.5 y=23.4 mmF1C2: 100 nF 1206 on VBUS [C24497] x=11.5 y=8.8 mmC2R3: 68 R 1206, D+ series [C17976] x=18.5 y=19.5 mmR3D1: 3.6 V zener, D+ clamp [C725453] x=23.9 y=19.5 mmD1R4: 68 R 1206, D- series [C17976] x=18.5 y=12.5 mmR4D2: 3.6 V zener, D- clamp [C725453] x=23.9 y=12.5 mmD2R5: 2.2 k 1206, D- pull-up (low speed) [C17948] x=18.5 y=8.6 mmR5C1: 10 uF 1206, +5V bulk [C9807] x=18.5 y=24.4 mmC1U1: ATmega8A-AU, TQFP-32 [C16190] x=37.0 y=16.0 mmU1Y1: 12 MHz crystal 3225 [C9002] x=29.6 y=12.6 mmY1C3: 22 pF 0805, XTAL1 load [C1804] x=29.6 y=9.0 mmC3C4: 22 pF 0805, XTAL2 load [C1804] x=29.6 y=16.4 mmC4C5: 100 nF 1206, VCC pin 4 [C24497] x=37.6 y=23.0 mmC5C7: 100 nF 1206, AVCC pin 18 [C24497] x=42.6 y=23.0 mmC7R6: 10 k 1206, RESET pull-up [C17902] x=31.0 y=23.0 mmR6C6: 100 nF 1206, VCC pin 6 [C24497] x=37.0 y=9.0 mmC6LED1: Red LED: programming (PC1 low) [C965798] x=31.0 y=26.8 mmLED1R7: 1 k 1206, LED1 series [C4410] x=36.0 y=26.8 mmR7LED2: Green LED: USB ready (PC0 low) [C2986059] x=31.0 y=29.6 mmLED2R8: 1 k 1206, LED2 series [C4410] x=36.0 y=29.6 mmR8J4: 2x3 header: flash THIS ATmega8A (self-programming port) [C65114] x=37.5 y=3.6 mmJ4JP2: 1x2 header: slow SCK jumper (PC2 to GND) [C492401] x=29.8 y=4.0 mmJP2U4: 74LVC8T245PW 8-bit dual-supply transceiver, TSSOP-24 [C458788] x=50.2 y=10.2 mmU4C10: 100 nF 1206, U4 VCCA [C24497] x=50.2 y=16.6 mmC10U5: 74LVC1T45GW 1-bit dual-supply transceiver (MISO back), SC-88 [C478004] x=55.6 y=16.4 mmU5R10: 10 k 1206, OE# pull-up (outputs off while the ATmega8A is in reset) [C17902] x=55.6 y=11.6 mmR10R11: 100 k 1206, MOSI_M pull-down (no floating input) [C17900] x=55.6 y=5.0 mmR11C12: 100 nF 1206, U5 VCCA [C24497] x=59.4 y=16.0 mmC12R12: 100 k 1206, SCK_M pull-down [C17900] x=59.4 y=9.6 mmR12R13: 100 k 1206, RST_M pull-down [C17900] x=59.4 y=3.6 mmR13C13: 100 nF 1206, U5 VCCB [C24497] x=63.0 y=16.0 mmC13C11: 100 nF 1206, U4 VCCB [C24497] x=63.0 y=9.6 mmC11U3: AP2112K-3.3 LDO, SOT-25 [C51118] x=48.8 y=29.2 mmU3C8: 10 uF 1206, LDO input [C9807] x=53.4 y=29.2 mmC8C9: 10 uF 1206, LDO output [C9807] x=58.2 y=29.2 mmC9LED3: Yellow LED: powering the target [C965803] x=48.6 y=25.4 mmLED3R9: 1 k 1206, LED3 series [C4410] x=53.4 y=25.4 mmR9F2: PTC 200 mA 1206, target supply limit [C207035] x=58.2 y=25.4 mmF2JP1: 1x3 header: target supply 5 V (1-2) / 3.3 V (2-3) / off [C492402] x=51.0 y=21.7 mmJP1J2: 2x5 box header: standard AVR 10-pin ISP [C5665] x=79.0 y=16.0 mmJ2J3: 2x3 header: standard AVR 6-pin ISP [C65114] x=68.4 y=16.0 mmJ3
RefPartLCSCX mmY mmRotSize mm (est.)
U474LVC8T245PW 8-bit dual-supply transceiver, TSSOP-24C45878850.210.20°6.6 x 8.4
U574LVC1T45GW 1-bit dual-supply transceiver (MISO back), SC-88C47800455.616.40°2.6 x 2.6
C10100 nF 1206, U4 VCCAC2449750.216.60°4.6 x 2.6
C11100 nF 1206, U4 VCCBC2449763.09.690°4.6 x 2.6
C12100 nF 1206, U5 VCCAC2449759.416.090°4.6 x 2.6
C13100 nF 1206, U5 VCCBC2449763.016.090°4.6 x 2.6
R1010 k 1206, OE# pull-up (outputs off while the ATmega8A is in reset)C1790255.611.690°4.6 x 2.6
R11100 k 1206, MOSI_M pull-down (no floating input)C1790055.65.090°4.6 x 2.6
R12100 k 1206, SCK_M pull-downC1790059.49.690°4.6 x 2.6
R13100 k 1206, RST_M pull-downC1790059.43.690°4.6 x 2.6

TARGET POWER0 / 7 placed · box x 46.6 to 64.4, y 19.6 to 31.4 mm

USB-CV-USBATMEGA8ALEVEL SHIFTTARGET POWERISP 10 / 6 PINJ1: USB-C 16-pin receptacle (USB 2.0) [C165948] x=3.8 y=16.0 mmJ1U2: USBLC6-2SC6 ESD on D+ / D- [C7519] x=11.5 y=16.0 mmU2R1: 5.1 k 1206, CC1 pull-down [C26033] x=11.5 y=20.4 mmR1R2: 5.1 k 1206, CC2 pull-down [C26033] x=11.5 y=11.6 mmR2F1: PTC 500 mA 1206, VBUS to +5V [C163512] x=11.5 y=23.4 mmF1C2: 100 nF 1206 on VBUS [C24497] x=11.5 y=8.8 mmC2R3: 68 R 1206, D+ series [C17976] x=18.5 y=19.5 mmR3D1: 3.6 V zener, D+ clamp [C725453] x=23.9 y=19.5 mmD1R4: 68 R 1206, D- series [C17976] x=18.5 y=12.5 mmR4D2: 3.6 V zener, D- clamp [C725453] x=23.9 y=12.5 mmD2R5: 2.2 k 1206, D- pull-up (low speed) [C17948] x=18.5 y=8.6 mmR5C1: 10 uF 1206, +5V bulk [C9807] x=18.5 y=24.4 mmC1U1: ATmega8A-AU, TQFP-32 [C16190] x=37.0 y=16.0 mmU1Y1: 12 MHz crystal 3225 [C9002] x=29.6 y=12.6 mmY1C3: 22 pF 0805, XTAL1 load [C1804] x=29.6 y=9.0 mmC3C4: 22 pF 0805, XTAL2 load [C1804] x=29.6 y=16.4 mmC4C5: 100 nF 1206, VCC pin 4 [C24497] x=37.6 y=23.0 mmC5C7: 100 nF 1206, AVCC pin 18 [C24497] x=42.6 y=23.0 mmC7R6: 10 k 1206, RESET pull-up [C17902] x=31.0 y=23.0 mmR6C6: 100 nF 1206, VCC pin 6 [C24497] x=37.0 y=9.0 mmC6LED1: Red LED: programming (PC1 low) [C965798] x=31.0 y=26.8 mmLED1R7: 1 k 1206, LED1 series [C4410] x=36.0 y=26.8 mmR7LED2: Green LED: USB ready (PC0 low) [C2986059] x=31.0 y=29.6 mmLED2R8: 1 k 1206, LED2 series [C4410] x=36.0 y=29.6 mmR8J4: 2x3 header: flash THIS ATmega8A (self-programming port) [C65114] x=37.5 y=3.6 mmJ4JP2: 1x2 header: slow SCK jumper (PC2 to GND) [C492401] x=29.8 y=4.0 mmJP2U4: 74LVC8T245PW 8-bit dual-supply transceiver, TSSOP-24 [C458788] x=50.2 y=10.2 mmU4C10: 100 nF 1206, U4 VCCA [C24497] x=50.2 y=16.6 mmC10U5: 74LVC1T45GW 1-bit dual-supply transceiver (MISO back), SC-88 [C478004] x=55.6 y=16.4 mmU5R10: 10 k 1206, OE# pull-up (outputs off while the ATmega8A is in reset) [C17902] x=55.6 y=11.6 mmR10R11: 100 k 1206, MOSI_M pull-down (no floating input) [C17900] x=55.6 y=5.0 mmR11C12: 100 nF 1206, U5 VCCA [C24497] x=59.4 y=16.0 mmC12R12: 100 k 1206, SCK_M pull-down [C17900] x=59.4 y=9.6 mmR12R13: 100 k 1206, RST_M pull-down [C17900] x=59.4 y=3.6 mmR13C13: 100 nF 1206, U5 VCCB [C24497] x=63.0 y=16.0 mmC13C11: 100 nF 1206, U4 VCCB [C24497] x=63.0 y=9.6 mmC11U3: AP2112K-3.3 LDO, SOT-25 [C51118] x=48.8 y=29.2 mmU3C8: 10 uF 1206, LDO input [C9807] x=53.4 y=29.2 mmC8C9: 10 uF 1206, LDO output [C9807] x=58.2 y=29.2 mmC9LED3: Yellow LED: powering the target [C965803] x=48.6 y=25.4 mmLED3R9: 1 k 1206, LED3 series [C4410] x=53.4 y=25.4 mmR9F2: PTC 200 mA 1206, target supply limit [C207035] x=58.2 y=25.4 mmF2JP1: 1x3 header: target supply 5 V (1-2) / 3.3 V (2-3) / off [C492402] x=51.0 y=21.7 mmJP1J2: 2x5 box header: standard AVR 10-pin ISP [C5665] x=79.0 y=16.0 mmJ2J3: 2x3 header: standard AVR 6-pin ISP [C65114] x=68.4 y=16.0 mmJ3
RefPartLCSCX mmY mmRotSize mm (est.)
U3AP2112K-3.3 LDO, SOT-25C5111848.829.20°3.0 x 3.0
JP11x3 header: target supply 5 V (1-2) / 3.3 V (2-3) / offC49240251.021.70°7.6 x 2.5
C810 uF 1206, LDO inputC980753.429.20°4.6 x 2.6
C910 uF 1206, LDO outputC980758.229.20°4.6 x 2.6
F2PTC 200 mA 1206, target supply limitC20703558.225.40°4.6 x 2.6
LED3Yellow LED: powering the targetC96580348.625.40°2.6 x 1.6
R91 k 1206, LED3 seriesC441053.425.40°4.6 x 2.6

ISP 10 / 6 PIN0 / 2 placed · box x 65.0 to 83.6, y 4.0 to 28.0 mm

USB-CV-USBATMEGA8ALEVEL SHIFTTARGET POWERISP 10 / 6 PINJ1: USB-C 16-pin receptacle (USB 2.0) [C165948] x=3.8 y=16.0 mmJ1U2: USBLC6-2SC6 ESD on D+ / D- [C7519] x=11.5 y=16.0 mmU2R1: 5.1 k 1206, CC1 pull-down [C26033] x=11.5 y=20.4 mmR1R2: 5.1 k 1206, CC2 pull-down [C26033] x=11.5 y=11.6 mmR2F1: PTC 500 mA 1206, VBUS to +5V [C163512] x=11.5 y=23.4 mmF1C2: 100 nF 1206 on VBUS [C24497] x=11.5 y=8.8 mmC2R3: 68 R 1206, D+ series [C17976] x=18.5 y=19.5 mmR3D1: 3.6 V zener, D+ clamp [C725453] x=23.9 y=19.5 mmD1R4: 68 R 1206, D- series [C17976] x=18.5 y=12.5 mmR4D2: 3.6 V zener, D- clamp [C725453] x=23.9 y=12.5 mmD2R5: 2.2 k 1206, D- pull-up (low speed) [C17948] x=18.5 y=8.6 mmR5C1: 10 uF 1206, +5V bulk [C9807] x=18.5 y=24.4 mmC1U1: ATmega8A-AU, TQFP-32 [C16190] x=37.0 y=16.0 mmU1Y1: 12 MHz crystal 3225 [C9002] x=29.6 y=12.6 mmY1C3: 22 pF 0805, XTAL1 load [C1804] x=29.6 y=9.0 mmC3C4: 22 pF 0805, XTAL2 load [C1804] x=29.6 y=16.4 mmC4C5: 100 nF 1206, VCC pin 4 [C24497] x=37.6 y=23.0 mmC5C7: 100 nF 1206, AVCC pin 18 [C24497] x=42.6 y=23.0 mmC7R6: 10 k 1206, RESET pull-up [C17902] x=31.0 y=23.0 mmR6C6: 100 nF 1206, VCC pin 6 [C24497] x=37.0 y=9.0 mmC6LED1: Red LED: programming (PC1 low) [C965798] x=31.0 y=26.8 mmLED1R7: 1 k 1206, LED1 series [C4410] x=36.0 y=26.8 mmR7LED2: Green LED: USB ready (PC0 low) [C2986059] x=31.0 y=29.6 mmLED2R8: 1 k 1206, LED2 series [C4410] x=36.0 y=29.6 mmR8J4: 2x3 header: flash THIS ATmega8A (self-programming port) [C65114] x=37.5 y=3.6 mmJ4JP2: 1x2 header: slow SCK jumper (PC2 to GND) [C492401] x=29.8 y=4.0 mmJP2U4: 74LVC8T245PW 8-bit dual-supply transceiver, TSSOP-24 [C458788] x=50.2 y=10.2 mmU4C10: 100 nF 1206, U4 VCCA [C24497] x=50.2 y=16.6 mmC10U5: 74LVC1T45GW 1-bit dual-supply transceiver (MISO back), SC-88 [C478004] x=55.6 y=16.4 mmU5R10: 10 k 1206, OE# pull-up (outputs off while the ATmega8A is in reset) [C17902] x=55.6 y=11.6 mmR10R11: 100 k 1206, MOSI_M pull-down (no floating input) [C17900] x=55.6 y=5.0 mmR11C12: 100 nF 1206, U5 VCCA [C24497] x=59.4 y=16.0 mmC12R12: 100 k 1206, SCK_M pull-down [C17900] x=59.4 y=9.6 mmR12R13: 100 k 1206, RST_M pull-down [C17900] x=59.4 y=3.6 mmR13C13: 100 nF 1206, U5 VCCB [C24497] x=63.0 y=16.0 mmC13C11: 100 nF 1206, U4 VCCB [C24497] x=63.0 y=9.6 mmC11U3: AP2112K-3.3 LDO, SOT-25 [C51118] x=48.8 y=29.2 mmU3C8: 10 uF 1206, LDO input [C9807] x=53.4 y=29.2 mmC8C9: 10 uF 1206, LDO output [C9807] x=58.2 y=29.2 mmC9LED3: Yellow LED: powering the target [C965803] x=48.6 y=25.4 mmLED3R9: 1 k 1206, LED3 series [C4410] x=53.4 y=25.4 mmR9F2: PTC 200 mA 1206, target supply limit [C207035] x=58.2 y=25.4 mmF2JP1: 1x3 header: target supply 5 V (1-2) / 3.3 V (2-3) / off [C492402] x=51.0 y=21.7 mmJP1J2: 2x5 box header: standard AVR 10-pin ISP [C5665] x=79.0 y=16.0 mmJ2J3: 2x3 header: standard AVR 6-pin ISP [C65114] x=68.4 y=16.0 mmJ3
RefPartLCSCX mmY mmRotSize mm (est.)
J22x5 box header: standard AVR 10-pin ISPC566579.016.00°8.9 x 20.3
J32x3 header: standard AVR 6-pin ISPC6511468.416.00°5.1 x 7.6

Nets and trace widths1 oz copper, with margin

NetWidthNotes
+5V, VBUS0.5 mmBoard + target up to about 0.25 A.
VTGT, VTGT_SUP, +3V30.4 mmTarget supply up to 200 mA (F2).
GNDpour on both layersStitching vias around the USB pair and the crystal.
USB_DP / USB_DN (and _J)0.25 mm pairLow-speed USB: short and together, no stubs.
XTAL1 / XTAL20.25 mmAs short as possible, GND pour around, nothing else under Y1.
_M, _T, BUSY_N, others0.25 mmPlain signals; keep SCK_T away from MISO_T on the way to the headers.

Order of work

  1. In EasyEDA PCB draw the outline 84 x 32 mm, 2 mm corners, two 3.2 mm non-plated holes at (3.5,3.5), (3.5,28.5) mm.
  2. Import the schematic (Design > Update/Convert Schematic to PCB). Check every footprint against its datasheet first.
  3. Place block by block with the X / Y tables, ticking each part here.
  4. Draw one rectangle per block on the Top Silkscreen layer with its title (the dashed boxes).
  5. Route the USB pair and the crystal first, then power, then the ISP lines. Pour GND on both layers.
  6. Run DRC. Add silkscreen: SafeASP, JP1 5V | 3V3, JP2 SLOW, J4 SELF-PROG, LED names (BUSY, USB, TGT PWR), ISP pin names.
  7. Export Gerber, BOM and pick-and-place.